Issues

• [P0][PCB 00] Working-board routing audit: regional fix tracker (2026-10-19)

  Open-Racing-Telemetry/rtlm#25 · Filter by author torbenconto opened on Oct 20, 2026

• [P2][PCB 22] Board-wide finish: route cleanup, test access and fabrication release checks

  Open-Racing-Telemetry/rtlm#24 · Filter by author torbenconto opened on Oct 20, 2026

• [P0][PCB 21] Pack measurement low side U8/U9: finish LDO/DC-DC link and ADC decoupling

  Open-Racing-Telemetry/rtlm#23 · Filter by author torbenconto opened on Oct 20, 2026

• [P1][PCB 20] CAN region IC7/IC8/J18: complete rails, controls and paired bus routing

  Open-Racing-Telemetry/rtlm#22 · Filter by author torbenconto opened on Oct 20, 2026

• [P1][PCB 19] LED driver/status LEDs: finish supply rails and remove redundant vias

  Open-Racing-Telemetry/rtlm#21 · Filter by author torbenconto opened on Oct 20, 2026

• [P1][PCB 18] Analog inputs J13–J16/IC6: connect protection grounds and buffer power

  Open-Racing-Telemetry/rtlm#20 · Filter by author torbenconto opened on Oct 20, 2026

• [P1][PCB 17] Temperature region J9–J12/IC5: finish analog returns and buffer supplies

  Open-Racing-Telemetry/rtlm#19 · Filter by author torbenconto opened on Oct 20, 2026

• [P1][PCB 16] ADC U6/U7 and shared buses: complete reference, SPI and I2C pull-ups

  Open-Racing-Telemetry/rtlm#18 · Filter by author torbenconto opened on Oct 20, 2026

• [P1][PCB 15] Pulse inputs J5–J8/U5: finish clamp rails, filter grounds and logic outputs

  Open-Racing-Telemetry/rtlm#17 · Filter by author torbenconto opened on Oct 20, 2026

• [P0][PCB 14] Pulse/sensor supply IC4: connect planes, enable, fault and voltage monitor

  Open-Racing-Telemetry/rtlm#16 · Filter by author torbenconto opened on Oct 20, 2026

• [P1][PCB 13] RTC U10/BT1: connect supplies and repair sub-minimum I2C tracks

  Open-Racing-Telemetry/rtlm#15 · Filter by author torbenconto opened on Oct 20, 2026

• [P0][PCB 12] LoRa U4/Y2: complete supplies, PA feed and MCU control connections

  Open-Racing-Telemetry/rtlm#14 · Filter by author torbenconto opened on Oct 20, 2026

• [P1][PCB 11] LoRa RF chain: ground matching network and verify tuned geometry

  Open-Racing-Telemetry/rtlm#13 · Filter by author torbenconto opened on Oct 20, 2026

• [P1][PCB 10] SD J17: complete socket power/detect and retune the six-line bus

  Open-Racing-Telemetry/rtlm#12 · Filter by author torbenconto opened on Oct 20, 2026

• [P0][PCB 09] USB J1/U3/R3/R4: reroute as a real differential pair and ground ESD

  Open-Racing-Telemetry/rtlm#11 · Filter by author torbenconto opened on Oct 20, 2026

• [P0][PCB 08] IC1 crystal Y1: remove XTAL_N vias and create a quiet local loop

  Open-Racing-Telemetry/rtlm#10 · Filter by author torbenconto opened on Oct 20, 2026

• [P1][PCB 07] IC1 reset/boot/UART: finish boot input and ground strap resistors

  Open-Racing-Telemetry/rtlm#9 · Filter by author torbenconto opened on Oct 20, 2026

• [P0][PCB 06] IC1 supplies: finish decoupling, filtered supply and exposed-pad ground

  Open-Racing-Telemetry/rtlm#8 · Filter by author torbenconto opened on Oct 20, 2026

• [P0][PCB 02] Northeast isolation boundary: extend keepouts to all six layers

  Open-Racing-Telemetry/rtlm#5 · Filter by author torbenconto opened on Oct 20, 2026
  1

• [P0][PCB 01] Board-wide: lock six-layer rules, impedance geometry and power budgets

  Open-Racing-Telemetry/rtlm#4 · Filter by author torbenconto opened on Oct 20, 2026